GSD Series Screwdriver

DSD series universal electric screwdriver

DSD electric screwdriver driver is highly adaptable and supports mainstream screw machine controllers in the market.
Interface parameter settings, convenient user debugging and easier to use

16 tasks can be switched through DI or 485 communication

Special electric screwdriver software supports real-time display of torque curve and historical curve viewing

Wide torque range, 0.6~240kgf.cm

Typical applications:
LED, plastic toys, hardware, home appliances, power tools, Bluetooth products, car audio, car lampshades, car air conditioners, energy storage products, automobiles and peripheral products

YKD3722M is a high performance 3 phase stepper driver which is based on new 32 bit DSP technology, driver voltage AC110~220V.

86mm Series 2 Phase Open-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK86HB65-04A     1.8 65 3.2 4.0 0.65 3.9 1000 1.7 8 YK86HB80-04A 1.8 80 4.5 6.0 0.4 3.5 1400 2.3 8 YK86HB118-06A 1.8 118 8.5 6.0 0.6 6.5 2700 3.8 8 YK86HB156-06A 1.8 156 12.0 6.2 0.7 9.0 4000 5.3 8 Dimensions Dimensions Model  Shaft Diameter D(mm)  Shaft Type (mm) Shaft Length L1 (mm)    YK86HB65-04A  9.5 Flat 1*25 32 YK86HB80-04A  12.7 Flat 1*25 32 YK86HB118-06A  12.7 Key 5*5*25 32 YK86HB156-06A  15.875 Key 5*5*25 32 Motor connection

Transmission rate: 2x100Mbps (full-duplex), refresh time: 100 axes x 1µs/axis transmission delay = 0.1ms

Supports 1ms synchronization cycle. For synchronization cycles less than 1ms, it can support synchronization in multiples of 250µs. This makes it suitable for real-time-critical applications such as engraving and milling machines and printing presses.

Through precise adjustment of the EtherCAT distributed clock, 300 nodes can be connected over a distance of 120m with 15ns synchronization error and ±20ns synchronization jitter.

Using an RJ45 industrial Ethernet cable, the system allows for quick connection, significantly reducing wiring workload.

Stepper drive auto-setup measures motor parameters and configures motor current control and anti-resonance gain settings.

60mm Series 2 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MR Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) YK260EC65E1 1.8 87 2.0 5.0 0.3 1.2 490 1.0 YK260EC86E1 1.8 108 3.0 5.0 0.4 2.0 690 1.3 YK260EC65E1-KZ01 1.8 87 2.0 5.0 0.3 1.2 490 1.0            YK260EC86E1-KZ01              1.8 108 3.0 5.0 0.4 2.0 690 1.3 Suitable drive model: SSD2205M Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK260EC65E1 8 Flat 0.5*20 24 YK260EC86E1 8 Flat 0.5*20 24 YK260EC65E1-KZ01 8 Flat 0.5*25 30 YK260EC86E1-KZ01 8 Flat 0.5*25 30 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Motor standard cable: 1.5m (optional 2m/3m) Encoder standard cable: 1.5m (optional 2m/3m) Motor connection

MCC800P is a PCI-based motion control card for controlling stepper motors and servo systems. Motion planning through ARM and FPGA, pulse commands can be output, which can control 1-8 axes servo or stepper motor at the same time. The maximum frequency of each axis is 4MHz, and the 8-axis encoder input signal can be detected. It supports linear and circular interpolation, supports trapezoidal and S-shaped acceleration and deceleration point-to-point motion control, and supports speed/positoion change during motion. The position command can be output by single pulse (pulse + direction) or double pulse (CW + CCW pulse); it can be a differential output circuit or a single-ended output circuit.
MCC800P matched terminal board has multiple general I/Os, supports high-speed position latching and position comparison output. External bus I/O expansion greatly satisfies customers' various control requirements for I/O.

This product is equipped with a dynamic link library under Windows XP/Win7, which is convenient for customers to write their own application software. At the same time, it provides motion debugging software, which can demonstrate the function of this card, it also can be used to tests the operation of motion control cards, motors and drives and motion platforms.

Typical Application:

Widely used in PCB industry, semiconductor packaging industry, electronic processing industry, sheet metal processing industry, testing industry, such as: PCB drilling machine, PCB punching machine, solid crystal machine, ultrasonic wire bonding machine.