New Original AS3-04BAI Yako AC Servo Drive

YKE2608MH-IO Spontaneous Impulse Stepper Drive  YKE2608MH-IO is a high-performance stepper driver based on a new generation of digital control technology. The control mode of the driver is spontaneous pulse speed control. There are 16 segments of speed can be set by 4 DIP switches, and any speed within the range can be set through the upper computer. Three-way photoelectric isolation digital input, the driver supports motor parameter identification and phase memory functions; Its similar servo control principle, unique circuit design, superior software algorithm processing can make the motor running stably at low speed, and accurate current control technology greatly reduces the motor fever.  Performance:  32-bit DSP control, low noise and superior vibration performance Three-way optocoupler isolated digital signal input, compatible with 5V/24V signals, support common cathode and anode connection mode Using the latest resonance suppression algorithm, it has excellent stationarity at medium and low speed With 8 current, 16 speed optional Running current, speed, acceleration and deceleration can be set in the upper computer debugging software The lock current can be set by the upper computer, the default setting current is 50% Small size, volume 151*94*54 (mm³), weight 0.5kg  Application:  YKE2608MH-IO is mainly used for speed controling, loading machine, unloading machine, docking station, logistics transmission, load shifting equipment, electronic equipment Dimensions: YKE2608MH-IO Roted Speed Setting: The / speed 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RPM 50 150 250 350 450 550 650 750 850 950 5 10 20 30 40 100 SW8 ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF SW7 ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF SW6 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF SW5 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW4=OFF Control Mode 2 lN1 lN2 statue invalid invalid locking valid invalid CW invalid valid locking valid valid BW SW4=ON Control Mode 1 lN1 lN2 statue invalid invalid locking valid invalid CW invalid valid BW valid valid locking YKE2608MH-IO Current Setting: RMS Default(2.00) 2.57 3.14 3.71 4.28 4.86 5.43 6.00 Peak Default(2.40) 3.08 3.77 4.45 5.14 5.83 6.52 7.20 SW3 ON ON ON ON OFF OFF OFF OFF SW2 ON ON OFF OFF ON ON OFF OFF SW1 ON OFF ON OFF ON OFF ON OFF Terminal Introduction: Symbol Function Specification PWR Power indicator When power on, the green indicator lights up.  TM Work indicator Pulse signal indicator, when there is continuous pulse input, the green indicator light flashes, otherwise the green indicator light is always on. O.C Fault indicator When over current or under voltage, the red indicator lights up. ln1+ input signal 1 electro-optical isolation + Connect signal power, for +5~+24V, when over +24V the ln1- need to connect current-limiting resistance. ln1- input signal 1 electro-optical isolation - It requires: low level 0~0.5V, high level 5~24V. ln2+ input signal 2 electro-optical isolation + Connect signal power, for +5~+24V, when over +24V the ln2- need to connect current-limiting resistance. ln2- input signal 2 electro-optical isolation - It requires: low level 0~0.5V, high level 5~24V. MF+ Motor free signal + Connect signal power, for +5~+24V, when over +24V the MF- need to connect current-limiting resistance. MF- Input signal - When it's in low level, cut off the motor current, and the drive stops working -V Power supply- AC18~80/DC30~110V +V Power supply + +A,-A   Motor connection +B,-B

YKD2608MH open-loop stepper drive suitable for 86-130mm(NEMA34-57) 2 phase open-loop stepper motors. Mainly used in kinds machines and equipment.

  MCC800S high performance motion control card, a PCI bus based motion controller for controlling stepper motors and servo systems. Motion planning through ARM and FPGA, can control 1-8 axes servo or stepper motor, support 2-8 axes linear interpolation, arbitrary 2-axis plane circular interpolation, arbitrary 3-axis space circular/coil interpolation. Each axis has a maximum pulse frequency of 4MHz and an encoder input signal. Interpolation motion has S-type speed curve, small circle speed limit, PWM vector speed follow, backlash compensation, system maximum acceleration limit and other functions.
    MCC800S matched terminal board has multi-channel general I/O, supporting high-speed position latching and position comparison output, continuous interpolation buffer I/O, external bus I/O expansion, greatly satisfying customers' various control requirements for I/O .

     This product is equipped with a dynamic link library under Windows XP/Win7, which is convenient for customers to write their own application software. At the same time, it provides motion debugging software, which can demonstrate the function of this card. it also can be used to tests the operation of motion control cards, motors, drives and motion platforms.    

Typical Application:           

Electronic manufacturing processing and testing equipment, engraving equipment, cutting equipment, placement machine, laser processing equipment, dispensing equipment, spraying, welding equipment, loading and unloading robots, etc.

42mm Series 2 Phase Open-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK42HB38-02A 1.8 40 0.4 2.0 1.06 2.0 54 0.3 4 YK42HB47-02A 1.8 40 0.48 2.0 1.35 2.9 77 0.32 4 YK42HB60-02A 1.8 40 0.72 2.0 1.8 3.7 110 0.5 4 Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK42HB38-02A 5.0 Key 0.5*15 24 YK42HB47-02A 5.0 Key 0.5*15 24 YK42HB60-02A 5.0 Key 0.5*15 24 Motor connection

110mm Series 3 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK385EC127A1 1.2 156 12 4.2 1.2 13 9320 6.5 3 YK385EC156A1 1.2 238 20 4.2 1.88 18 12510 10.4 3 Suitable drive model: MS-L3 Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK3110EC140C1 19 Key 6*6*30 39 YK3110EC220C1 19 Key 6*6*30 39 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Encoder standard cable: 2m (optional 8m/10m) No more motor cable needed Motor connection

MCC800P is a PCI-based motion control card for controlling stepper motors and servo systems. Motion planning through ARM and FPGA, pulse commands can be output, which can control 1-8 axes servo or stepper motor at the same time. The maximum frequency of each axis is 4MHz, and the 8-axis encoder input signal can be detected. It supports linear and circular interpolation, supports trapezoidal and S-shaped acceleration and deceleration point-to-point motion control, and supports speed/positoion change during motion. The position command can be output by single pulse (pulse + direction) or double pulse (CW + CCW pulse); it can be a differential output circuit or a single-ended output circuit.
MCC800P matched terminal board has multiple general I/Os, supports high-speed position latching and position comparison output. External bus I/O expansion greatly satisfies customers' various control requirements for I/O.

This product is equipped with a dynamic link library under Windows XP/Win7, which is convenient for customers to write their own application software. At the same time, it provides motion debugging software, which can demonstrate the function of this card, it also can be used to tests the operation of motion control cards, motors and drives and motion platforms.

Typical Application:

Widely used in PCB industry, semiconductor packaging industry, electronic processing industry, sheet metal processing industry, testing industry, such as: PCB drilling machine, PCB punching machine, solid crystal machine, ultrasonic wire bonding machine.

86mm Series 3 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK385EC127A1 1.2 147 7.5 4.5 2.6 17 3960 4.26 3 YK385EC156A1 1.2 176 12 3.0 2.34 18.33 4500 6.5 3 Suitable drive model: MS-L3 Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK385EC127A1 14 Key 5*5*25 40 YK385EC156A1 14 Key 5*5*25 40 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Encoder standard cable: 2m (optional 8m/10m) No more motor cable needed Motor connection