110mm 3 Phase DSP Close-loop Stepper Motor

86mm Series 3 Phase Close-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK385EC127A1 1.2 147 7.5 4.5 2.6 17 3960 4.26 3 YK385EC156A1 1.2 176 12 3.0 2.34 18.33 4500 6.5 3 Suitable drive model: MS-L3 Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK385EC127A1 14 Key 5*5*25 40 YK385EC156A1 14 Key 5*5*25 40 Encoder Wiring Black GND Red +5V Blue/White EA- Blue EA+ Orange/White EB- Orange EB+ *Motor / Encoder cable: 0.3m Encoder standard cable: 2m (optional 8m/10m) No more motor cable needed Motor connection

AS3 Series 380V High power Servo Drive

YAKO new product launch!

YKA2811MA open-loop stepper drive, adjustable drive current range from 0.5A/phase - 8A/phase; protection of overvoltage, overheat and overcurrent.

This integrated stepper  motor integrates bus communication control technology, simple wiring, no losing step, lower heat, high speed, high torque, low cost and convenient maintenance. It is a cost-effective motion control product.

Transmission rate: 2x100Mbps (full-duplex), refresh time: 100 axes x 1µs/axis transmission delay = 0.1ms

Supports 1ms synchronization cycle. For synchronization cycles less than 1ms, it can support synchronization in multiples of 250µs. This makes it suitable for real-time-critical applications such as engraving and milling machines and printing presses.

Through precise adjustment of the EtherCAT distributed clock, 300 nodes can be connected over a distance of 120m with 15ns synchronization error and ±20ns synchronization jitter.

Using an RJ45 industrial Ethernet cable, the system allows for quick connection, significantly reducing wiring workload.

YKE5405M 5-phase Stepper Drive The YKE5405M is a high-performance digital stepper drive based on a new generation of digital control technology, specifically designed for five-phase motors. Compared to ordinary two-phase stepper drivers, its unique advantages include smoother low-speed operation and less low-speed resonance. At high speeds, it offers better start-stop performance and output levels. Internally, this driver employs a servo-like control principle, a unique circuit design, and superior software algorithm processing. Even under low microstepping conditions, it ensures smooth low-speed motor operation with low vibration and noise. Furthermore, its smooth and precise current control technology significantly reduces motor heat generation, making it highly effective in applications requiring responsiveness and smoothness. Features:  New generation 32-bit DSP control technology, offering high cost-effectiveness, excellent stability, and superior noise and vibration performance.  Optically isolated differential signal input, compatible with 5V/24V signals, adaptable to the signal requirements of different controllers.  Single/dual pulse function, adjustable via DIP switches.  Supports pulse smoothing control and pulse filtering functions, configurable according to actual usage scenarios. Features 16 levels of constant torque microstepping, supporting up to 125,000 microsteps.  Supports 8 levels of current DIP switch adjustment, with a maximum peak current of 4.9A. Maximum pulse response frequency up to 500kHz.  Voltage input range: DC20~50V.  Includes overvoltage, undervoltage, and overcurrent protection detection functions. Applications:  Primarily used in automated equipment for medical devices, semiconductors, and 3C non-standard products. It performs exceptionally well in devices where users expect low heat generation,  low noise, high stability, high response, and high precision. Dimensions: YKE5405M Microstep Setting Table PU/Rev 500 1000 1250 2000 2500 4000 5000 10000 12500 20000 25000 40000 50000 62500 100000 125000 SW8 ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF SW7 ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF SW6 ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF SW5 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW4: OFF=Half current          ON=Full Current YKE5405M Current Table Current RMS 0.5 0.7 1 1.5 2.0 2.5 3.0 3.5 Current Peak 0.7 1 1.4 2.1 2.8 3.5 4.2 4.9 SW3 ON ON ON ON OFF OFF OFF OFF SW2 ON ON OFF OFF ON ON OFF OFF SW1 ON OFF ON OFF ON OFF ON OFF YKE5405M Drive operation mode setting Mode Setting SW9 SW10 SW11 SW12 Functions Pulse input method Pulse smoothing control Pulse filter control Default direction control OFF PU+DR Enabler 200KHz Clockwise direction ON CW+CCW+ Disabler 500KHz Counterclockwise direction

MCC800P is a PCI-based motion control card for controlling stepper motors and servo systems. Motion planning through ARM and FPGA, pulse commands can be output, which can control 1-8 axes servo or stepper motor at the same time. The maximum frequency of each axis is 4MHz, and the 8-axis encoder input signal can be detected. It supports linear and circular interpolation, supports trapezoidal and S-shaped acceleration and deceleration point-to-point motion control, and supports speed/positoion change during motion. The position command can be output by single pulse (pulse + direction) or double pulse (CW + CCW pulse); it can be a differential output circuit or a single-ended output circuit.
MCC800P matched terminal board has multiple general I/Os, supports high-speed position latching and position comparison output. External bus I/O expansion greatly satisfies customers' various control requirements for I/O.

This product is equipped with a dynamic link library under Windows XP/Win7, which is convenient for customers to write their own application software. At the same time, it provides motion debugging software, which can demonstrate the function of this card, it also can be used to tests the operation of motion control cards, motors and drives and motion platforms.

Typical Application:

Widely used in PCB industry, semiconductor packaging industry, electronic processing industry, sheet metal processing industry, testing industry, such as: PCB drilling machine, PCB punching machine, solid crystal machine, ultrasonic wire bonding machine.

42mm Series 2 Phase Open-loop Stepper Motor  Step accuracy: 5% Temperature: 80℃Max Ambient temperature: -20℃-+50℃ Insulation resistance: 100MΩ Min 500VDC Pressure resistance: 500VAC 1 minute Radial runout: Maximum 0.02mm (450g load) Axial runout: Maximum 0.08mm (450g load) Specification Model Step Angle (°） Motor Lenth (L) Holding Torque (N.m) Rated Current (A) Resistance (Ω） Inductance (mH) Rotor Inertia (g.cm²） Weight (kg) Motor Leads YK42HB38-02A 1.8 40 0.4 2.0 1.06 2.0 54 0.3 4 YK42HB47-02A 1.8 40 0.48 2.0 1.35 2.9 77 0.32 4 YK42HB60-02A 1.8 40 0.72 2.0 1.8 3.7 110 0.5 4 Dimensions Dimensions Model Shaft Diameter D (mm) Shaft Type (mm) Shaft Length L1 (mm)  YK42HB38-02A 5.0 Key 0.5*15 24 YK42HB47-02A 5.0 Key 0.5*15 24 YK42HB60-02A 5.0 Key 0.5*15 24 Motor connection